← Ferramentas
Experimentar o CapCad →
Normas de sinalização horizontal por país
O documento de onde saem as marcas rodoviárias de cada país, uma ligação ao regulador e as dimensões que o CapCad desenha a partir dele — lidas diretamente do motor de desenho, por isso esta página e o programa nunca divergem.
Perú
Brasil
España
Portugal
France
UK
USA
México
Chile
Colombia
Argentina
Ecuador
Paraguay
Canada
الأردن
日本
مصر
Česko
Slovensko
Laos
Angola
Moçambique
السعودية
Indonesia
SADC
SIECA
Deutschland
Ireland
Nederland
Italia
India
Cuba
Entidade reguladora
Kementerian Perhubungan
Normas
Publicadas pela entidade emissora — ligamos à fonte em vez de alojar uma cópia, porque estes documentos são revistos.
PM 34 Tahun 2014 tentang Marka Jalan, as amended by PM 67 Tahun 2018
Kementerian Perhubungan · 2018
Line widths and cadences, the double line rules and their separation limits, and the colour article. The 2018 amendment replaced the whole annex and made yellow an identifier of national roads rather than a traffic rule.
PM 13 Tahun 2014 tentang Rambu Lalu Lintas
Kementerian Perhubungan · 2014
Sign numbering and sheet sizes. Codes carry no letter prefix and are scoped per table, so the same code means different signs in different tables. Stop, give way and the speed limit are all prohibition signs.
Pd T-12-2004-B, Penempatan Marka Jalan
Direktorat Jenderal Bina Marga · 2004
The hatched and chevron marking geometry, which the transport regulation does not give: stripe and border widths, spacing, and the 45 degree angle to the direction of travel.
Pedoman Desain Geometrik Jalan, Nomor 13/P/BM/2021
Direktorat Jenderal Bina Marga · 2021
Stopping and overtaking sight distances. This pedoman expressly revoked the 1997 inter-urban geometric standard.
Marcas longitudinais que o CapCad desenha (12)
| Marca | Referência normativa |
|---|---|
| Marka garis peringatan, 3 m + 1,5 m | Warning line announcing a solid line, 15 cm wide, 3 m mark and 1,5 m gap, placed at least 50 m before it (Gambar 7; placement Pasal 60(3)) |
| Marka larangan parkir atau berhenti (garis berbiku-biku) | Yellow zigzag line at the roadside forbidding parking or stopping, at least 10 cm wide and at least 1 m long (PM 34/2014 Pasal 43) |
| Marka membujur garis ganda dua garis utuh | Double solid line, each 12 cm, separated by at least 10 cm and at most 18 cm. Neither side may cross (PM 34/2014 Pasal 21) |
| Marka membujur garis ganda dua garis utuh - jalan nasional (kuning) | Double solid line on a jalan nasional, YELLOW. This is what PM 67/2018 Gambar 8 draws as the centre line of an undivided national road |
| Marka membujur garis ganda utuh dan putus-putus | Double line, one solid and one broken. Traffic on the broken side may cross, traffic on the solid side may not (PM 34/2014 Pasal 20) |
| Marka membujur garis putus-putus, 3 m + 5 m | Broken longitudinal line, 3 m mark and 5 m gap, for a design speed below 60 km/h (PM 34/2014 Pasal 18(2)a, Gambar 6a) |
| Marka membujur garis putus-putus, 5 m + 8 m | Broken longitudinal line, 5 m mark and 8 m gap, for a design speed of 60 km/h and above (PM 34/2014 Pasal 18(2)b, Gambar 6b) |
| Marka membujur garis utuh | Solid longitudinal line, at least 10 cm and drawn 12 cm in the Lampiran. Divides carriageways and forbids crossing (PM 34/2014 Pasal 17) |
| Marka membujur garis utuh - jalan nasional (kuning) | Solid longitudinal line on a jalan nasional, YELLOW because it is the jalur divider. Colour is a road-status identifier, not a traffic rule (PM 67/2018 Pasal 16(3)a) |
| Marka membujur garis utuh - tanda tepi jalan tol | Edge line of a jalan tol, at least 15 cm, solid (PM 34/2014 Pasal 17(4)) |
| Tanda tepi sisi kanan - jalan nasional (kuning) | Right edge line of a jalan nasional, solid YELLOW. Right is the offside here, the mirror of a drive-on-right country (PM 67/2018 Pasal 16(3)b) |
| Tanda tepi sisi kiri - jalan nasional (putih) | Left edge line of a jalan nasional, solid WHITE. Left is the nearside here (PM 67/2018 Pasal 16(4)b) |
Regras de zebrado comparar todos os países →
Cada desenho abaixo é produzido pelo próprio motor do CapCad, a partir dos números da sua linha — não é uma ilustração.
| Desenhado conforme a regra | Preset | Vão (m) | Franja (m) | Canalização (m) | Ângulo (°) |
|---|---|---|---|---|---|
| INDONESIA-CHEVRON | 1.0 | 0.3 | 0.15 | 90 | |
| INDONESIA-GARIS MIRING | 1.0 | 0.3 | 0.15 | 90 |
Desenhe estas marcas conforme a norma, no seu CAD
Cada dimensão desta página é um preset do CapCad — escolha o perfil do país e as marcas saem conforme o seu manual.